FAAC Electric Gate Repair Nationwide

FAAC Electric Gate Repair in Houston: What to Know First

FAAC electric gate repair in Houston typically runs between $95 and $350 for a standard service call, with most jobs completed same-day or within 24 hours once we diagnose the operator. We’re an independent FAAC service provider, which means we answer to you, not a manufacturer’s warranty department. If your FAAC gate is stuck open, refusing to close, or making a sound it never made before, call us at (361) 256-5955 and a live person will answer.

Call (361) 256-5955

This page is for Houston homeowners who own a FAAC swing or slide gate operator and want to know what’s wrong, what it costs, and whether it’s worth fixing. Cody Beckman and our technicians work on FAAC equipment every week. We’ll give you a written price before we touch anything.

How FAAC Products Fail – and How We Fix Them

• FAAC 400 Series swing operators with capacitor failure. The 400 and 412 models use a start capacitor that ages poorly in Houston’s heat and humidity. The gate will hum but not move, or move a few inches and quit. We test the capacitor under load, replace it with an OEM or equivalent-rated part, and verify the motor windings aren’t damaged before we call it fixed.
• FAAC 750 and 760 slide operators with worn limit switches. These operators use mechanical limit switches that drift over time. The gate stops short of the post or slams into it. We reset the limits, then listen to the motor draw at both ends of travel to catch a dying switch before it strands the gate open at 6 a.m.
• FAAC S418 and S450 hydraulic operators with low fluid or bypass valve issues. Hydraulic FAAC units lose fluid through seal seepage, especially after a few Houston summers. The gate opens slower than it used to and won’t hold position on an incline. We top off or flush the fluid, inspect the seals, and set the bypass pressure so the gate won’t crush a trash can or a dog.
• FAAC E024U control boards shorted by power surges. Houston thunderstorms and unstable line voltage kill control boards. The gate goes completely dead, no LED, no response from the keypad. We isolate the board, check the transformer and surge protection, and if the board is gone, we replace it with an OEM unit rather than a generic board that won’t talk to the FAAC obstacle detection correctly.
• FAAC photocells and safety edges misaligned after a storm or a bump. If a car taps the gate or high winds shift the post, the safety beam loses alignment and the gate refuses to close without holding the button. We realign the photo eyes, test the sensitivity settings, and make sure the auto-close delay is set so the gate doesn’t clip a car pulling through.

Our FAAC Electric Gate Repair Process

1. 1
   You call, a person answers. We ask what the gate is doing, what model you have if you know it, and when it started. Then we schedule a visit that works for your household.
2. 2
   We diagnose on-site before quoting. The technician checks the operator, control board, safety devices, and power supply. We open the housing and look for burnt components, moisture, and wear.
3. 3
   You get a written price. We tell you exactly what’s wrong and what the repair will cost before any work starts. If it doesn’t make sense to repair, we’ll tell you that too.
4. 4
   Parts decision, made together. For FAAC equipment, we recommend OEM parts where the safety logic matters, like control boards and obstacle detection. For wear items like capacitors or limit switches, we’ll offer a quality aftermarket option when it’s genuinely equivalent. You decide with the full price in front of you.
5. 5
   The repair and the test. We fix it, then run the gate through a full cycle with the safety devices deliberately triggered to confirm the FAAC obstacle detection responds correctly.
6. 6
   Cleanup and the 365-Day Done Right Promise. We wipe down the housing, put the cover back, and take a photo of the work area before we leave. Every FAAC repair carries our 365-Day Done Right Promise: if it’s not right, we make it right.

What FAAC Electric Gate Repair Costs in Houston

Most FAAC electric gate repair jobs in Houston fall into these ranges, depending on the model and what failed:

• Service call and diagnostic: $95 to $150, credited toward the repair if you proceed.
• Capacitor replacement on 400 Series: $40 to $95 parts and labor.
• Limit switch adjustment or replacement on 750/760: $85 to $150.
• Photocell realignment or replacement: $75 to $180.
• Control board replacement (E024U or similar): $225 to $450 depending on board and availability.
• Hydraulic fluid service and seal inspection on S418/S450: $120 to $220.

The exact number depends on which FAAC model you have and what failed. You’ll see it in writing before we start, and we don’t charge extra to show up and tell you what’s wrong. Call (361) 256-5955 for a free estimate over the phone.

Why Houston Homeowners Call Latch and Post Gate Repair Houston for FAAC Work

We’re a Cedarwell-family gate specialist, and we’ve been working on gates since 2009. That matters when you own a FAAC, because these operators aren’t interchangeable with the big-box brands. The hydraulic pressure settings, the board logic, the obstacle detection sensitivity all need a technician who knows the equipment, not someone learning on your driveway.

Every visit follows the Cedarwell C.A.R.E. values: Clean up like it’s our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, Explain the price before the work. We put on shoe covers before we step inside, lay drop cloths where we work, and send you a photo of the cleanup before we leave. We choose pet-safe lubricants where there’s a choice, and we can schedule around nap time if quiet matters.

We also service the other operators Houston families actually own: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. If your FAAC turns out to be beyond repair, we’ll show you options across those brands with straight numbers, not a sales pitch.

FAQs